What are the cutting techniques of overalls manufacturers?

Sewing is the basis of workwear manufacturers, cutting is the basis for sewing, custom workwear manufacturers should ensure the cutting accuracy when cutting, and reduce the error between the cut pieces and models. Next, let's take a look at the tailoring skills of Kosher’s custom workwear manufacturers. For the work clothes manufacturers, it is often necessary to cut the bed according to the size and quantity of the clothes, and to discharge the clothes according to the direction of the sample. The error between the clothes in the layers should be in compliance with the regulations. Incorrect method of cutting pieces will not only completely deviate from the design of the garment modeling structure, but also cause great waste. In the production of batch garments, it will bring great losses to the producers. Master the correct order. That is to say, there is no cross-cut, straight break, first mouth after the mouth, after the first small pieces of material after the whole material, piece by piece, take the material piece by piece. The left hand presses the support material, uses the force evenly and softly, can't tilt, the right hand pushes the knife to be relaxed and relaxed, has an order. Keep cutting knife vertical when cutting so as not to cause errors in each layer. Ensure that the knife is always sharp, but can not have edge gaps, in order to ensure that the edge of the piece is smooth and straight. Grasp the corner treatment. Where the corner of the piece is to be cut by cutting with different sides of the corner, it is not possible to cut corners in succession so as to ensure accurate positioning when cutting the knife edge, and the clipping must not exceed 3mm and be clear and durable. When the work clothes are cut, it is necessary to pay attention to the temperature of the knife, which is not too high, especially for synthetic fibers, which tends to cause discoloration, yellowing, adhesion, etc. on the edges of the clothes, and at the same time cause the blade to stick. Tooling cutting is not an independent job. Preparations such as painting and drawing should be performed before the clothes are trimmed. The material is laid on the cutting bed according to the required number of layers and the length of the material, and the clothing materials shall be laid out on the cutting bed in order to allow for drawing and cutting. For materials with large stretchability, it is necessary to store for several hours after the material is spread so that the stress can be retracted and then cut. Smoothness of the fabric: The surface of each layer of material must be smooth when it is laid, and there must be no wrinkles or unevenness. Otherwise, the pieces of clothing will be deformed, which will cause difficulties in the sewing work and adversely affect the effect and quality of the clothing. Alignment of cloth edges: When laying materials, it is required that the edges of each layer of cloth should be aligned and there should be no irregularity. Otherwise, it is easy to cause variation in size specifications of the cut pieces at the short side, resulting in a secondary film. The general requirements for cloth edges and inward openings are more stringent and neat and tidy. The difference should not exceed 2mm, because the mouth area will be used as the benchmark for future discharge. The other side can guarantee natural leveling. The direction is consistent and meets the requirements. Many materials have obvious positive and negative sides or have special directionality. In order to ensure consistent results when laying materials, the material should keep the same tension in the same direction and be as small as possible. To make the material smooth, if necessary, a certain tension must be applied. This force must be uniform and as small as possible to prevent wrinkling of internal stress due to uneven shrinkage. For materials with strips, grids, and patterns, in order to ensure or highlight the design effect, the work clothes processing factory requires the positive pattern to be in accordance with the design requirements in the material feeding process during the design of the panel layout. When paving materials, a bundle of fabrics with a narrow width should be used as the skin, ie, the width of the foundation. Carefully and meticulously prepare before cutting, grasp the correct cutting method, and then the next procedure of work clothes processing --- sewing. Some fabrics are water-strips (squares), and require the left and right symmetry of the front piece, and the rear piece of the water-strip (grid), you can take a film method. In this way, I feel that I need to save time compared to running alone. The tension of the fabric, especially the lining and the spinning, can be cut at intervals along the cloth edge, so that the fabric can wrinkle in order to prevent the internal stress from being uneven. The above are some of the basic skills of Krooss overalls custom-made manufacturers. They are also some of the key skills. It is a guarantee for the quality of garments that can be found by the workers in processing factories. It is also a guarantee for the sales of garments. Ke Rousi clothing () professional custom uniforms, professional wear, tailored wear on the use of flat and three-dimensional cutting combination techniques for your custom fit professional uniforms! Ke Rousi clothing - your staff's image design expert!