First, the correct use and maintenance of the electrode The electrode used in the laboratory is a composite electrode, its advantages are easy to use, not affected by oxidative or reducing substances, and the balance speed is faster. When in use, the rubber sleeve and the rubber sleeve at the lower end of the electrode filling port are completely removed to maintain the hydraulic pressure difference of the potassium chloride solution in the electrode. The following is a brief introduction to the use and maintenance of the electrode:
1. When the composite electrode is not in use, fully immerse the 3M potassium chloride solution in the vibrometer. Do not dip with washing liquid or other water-absorbing reagents.
2. Check the bulb at the front end of the glass electrode before using the bend tester. Under normal circumstances, the electrode should be transparent without cracks; the bulb should be filled with solution and no bubbles should exist.
3. When measuring a solution with a large concentration, shorten the measurement time as much as possible, and carefully clean it after use to prevent the test solution from adhering to the electrode and contaminating the electrode.
4. After cleaning the electrode, do not wipe the glass film with filter paper, and use filter paper to dry, avoid damage to the glass film, prevent cross-contamination, and affect measurement accuracy.
5. In the measurement, pay attention to the silver-silver chloride internal reference electrode of the electrode should be immersed in the chloride buffer solution in the bulb to avoid digital jumping phenomenon in the display part of the electricity meter. When using, be careful to gently rub the electrode a few times.
6. The electrode should not be used in strong acids, strong bases or other corrosive solutions.
7. It is strictly forbidden to use in dehydrating media such as absolute ethanol, potassium dichromate and the like.
2. Preparation and storage of standard buffer 1. The pH standard substance should be stored in a dry place. For example, mixed phosphate pH standard substance will deliquesce when the air humidity is high. Once deliquescent occurs, the pH standard substance cannot be used.
2. Prepare the pH standard solution using double distilled water or deionized water. If it is used for a 0.1-stage pH meter measurement, ordinary distilled water can be used.
3. The pH standard solution should be diluted with a smaller beaker to reduce the pH standard solution on the beaker wall. Plastic bags or other containers for storing pH standards should be rinsed several times with distilled water, and then poured into the prepared pH standard solution to ensure that the prepared pH standard solution is accurate.
4. The prepared standard buffer solution can be stored for 2-3 months. If it is found to be turbid, moldy or precipitated, it cannot be used any more.
5. The alkaline standard solution should be stored in a polyethylene bottle and sealed. Prevent carbon dioxide from entering the standard solution to form carbonic acid and lower its pH.
For more information on the pH tester, please visit: http://
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
Residential Sectional Garage Door
A typical version of an overhead garage door used in the past would have been built as a one-piece panel.The panel was mounted on each side with unequal parallelogram style hinge lifting mechanism. Newer versions of overhead garage doors are now generally built from several panels hinged together that roll along a system of tracks guided by rollers. The door is balanced by either a torsion spring system or a pair of extension springs.A remote controlled motorized mechanism for opening garage doors adds convenience, safety, and security
• Aluminum garage doors are low-cost, light, rust-proof, and feature low-maintenance. They are prone to denting because aluminum is not strong and they are energy-inefficient since aluminum is a highly conductivematerial.
• Fiberglass and vinyl garage doors are composite units, combining a steel core behind a fiberglass or vinyl skin. They have also polyurethane insulated base sections, or other type of foam insulation. These premium doors can match steel garage doors, and be a realistic imitation of wood (namely fiberglass units), but they may be more expensive than steel units.
• Steel doors have become common and are available in a variety of sizes and styles, provide strength and security, are cost-competitive, and may have optional insulating value. Extra strength is available with two or three layers of galvanized steel with a low gauge number (23-24 gauge steel panels).
• Wood garage doors offer aesthetic appeal, but they are high-maintenance and may be expensive. Low-priced wood garage doors may warp and break easily.
Residential Sectional Garage Door,Automatic Metal Sectional Garage Door,Standard Lift Garage Door Drum,Polyurethane Foam Garage Door
Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hfhighspeeddoor.com